Knastakselsæt Feuling 465 M8 oil cooled, chain drive 17-26

21 700,5 DKK

Feuling Race Series knastakselsæt med 465 Reaper-knast til oliekølede motorer
Læs mere

09251180 Feuling
  • Sættet indeholder Race Series oliepumpe, High Flow knastplade, 465 Reaper knastaksel, hydrauliske rulleløftere, stødstænger, Timken/Koyo knastlejer, ARP-bolte og møtrikker, pakninger og O-ringe
  • 465 Reaper giver kraftigt bundtræk med mærkbare stigninger over 2 800 RPM
  • Oliepumpe i 7075 billet-aluminium med magneter, der beskytter tandhjul og overtryksventil
  • Giver 27 % mere tryk- og returvolumen, 42 % mere returvolumen via tilpassede kanaler samt 46 % mere oliemængde til krumtapaksel og plejlstangsleje
  • Sænker motortemperaturen med 15°–35° og olietemperaturen med 15°–30° samt øger olietrykket med 15–30 PSI
  • Full travel-løftere med 0,200" slaglængde og langsommere aftømningshastighed for at håndtere høje fjedertryk
  • Kraftige stødstænger i ét stykke med .165" godstykkelse
  • Fremstillet i USA

Til Milwaukee-Eight (M8) oliekølede motorer. Passer ikke til '23–'26-modeller med VVT-motorer. Overfyld ikke olietanken, kontrollér olieniveauet, når motorcyklen står oprejst efter opvarmning.

Passer til: M8 oliekølede, kædedrift 17-26

Produkt-typ Camchest Kit
Tillverkarens Art. Nr. 7260

Race Series Camchest Kit with Full Travel Lifters

  • Quieter and smoother engine operation
  • Increases oil pressure, scavenge volume and engine oil flow
  • 15°-35° cooler engine temperatures
  • 15°-30° cooler oil temperatures
  • 15-30 more PSI of oil pressure
  • Eliminates wet sumping, blow by and oily air cleaners
  • Heavy duty .165" wall one piece pushrod reduces valvetrain harmonics and increase valve lift
  • Responds well with slip-on mufflers and/or a complete exhaust system and high-flow air cleaner
  • Responds well with increased bore and/or compression
  • Lifters have a full 0.200 of total travel designed with a slower bleed down rate to handle heavy valve spring pressures, increase engine RPM before valve float and feature increased roller clearance for steep ramped camshafts and clearance for the front exhaust camshaft lobe flange
  • Kit includes: Race Series high volume oil pump, High Flow billet camplate, Reaper Series camshaft, fulll-travel Race Series hydraulic roller lifters, fixed length pushrods, Timken/Koyo cam bearing, rocker arm studs and nuts, gaskets, O-rings, ARP cam/crank fasteners, washers, moly lube and Loctite
  • Made in the USA
  • Not for '23-'26 models with VVT motors.
  • With 465 Reaper cam (MCS 588026)
  • FEULING M8 OIL COOLED cam chest kits include all necessary components from top to bottom of the cam chest conveniently packaged in one part number
  • These combination kits not only ensure each individual part is designed to work and function together but to do so in total harmony
  • These cam chest kits take the guess work out of the ordering process and guarantees the engine builder maximum reliability, peak performance and the coolest engine and oil temperatures obtainable
  • 27% more pressure and scavenge gear volume over stock
  • 42% more scavenge volume with port sizing, matched passages and holes to the engine case
  • 46% more oil volume to the crankshaft and connecting rod bearing
  • Magnets in oil pump to help protect gears and pressure relief valve
  • Test results show 2 HP gain and 2 ft/lbs. of TQ gain to the rear wheel on Milwaukee Eight
  • NOTE: FEULING test results show a 50% reduction of engine sump oil level
  • The 465 Reaper is an accelerator, producing solid bottom end performance with substantial gains above 2,800 RPM when compared to stock
  • This direct bolt-in replacement for M8 engines can be used with stock valve springs, pushrods, lifters and exhaust
  • Use of performance valve-springs is not required but may result in a quieter, smoother running valve-train See Feuling #1107
  • Billet 7075 aluminum oil pump which is 50% harder and stronger than the factory pump holding tighter tolerances under temperature, deeper scavenge kidneys over HP+ oil pump
  • Due to the mass call volume & inquires with requests for the M8 oil pump back cover O-ring/seal groove, Feuling added the groove (5/11/21)
  • Although Feuling's in house testing on healthy engines did not show a benefit
  • The O-ring may have potential benefits in certain circumstances such as engines with higher cylinder leak down, poor sub-seal O-ring seal, raised sump hole & or sump plug (see M8 PRO TIP below) & looser lifter to lifter bore clearances
  • DO NOT OVERFILL OIL TANK
  • It is important to get the correct hot oil level in your bike
  • Note: The M8 oil pick up port is on the right side of the engine
  • Letting the bike idle or warm up on the kickstand will naturally fill the engine case and skew the oil level in the tank
  • We recommend the following steps to achieve proper oil level: 1
  • Check cold oil level
  • Ride the bike until operating temperature is reached
  • 3
  • Shut the bike off while still in the upright position. (This insures an accurate reading)
  • 4
  • Add or remove oil as needed
  • EXEMPT FROM EMISSIONS TAMPERING REGULATIONS UNDER CARB EO# D-881-1, 50 State legal CARB compliant: CARB EO# D-881-1
  • Feuling does not recommend tuning beyond stock emissions standards

Includes: • Race Series High Volume Oil Pump • High Flow Billet Camplate • Reaper Series 465 Camshaft • Race Series Hydraulic Roller Lifters • One Piece Pushrods • Timken/Koyo Cam Bearing • ARP Rocker Studs and Nuts • Camplate/OilPump Fasteners • O-Rings • Gaskets • Washers • Moly lube • Loctite

Fits: 17-26 M8 oil cooled, chain drive (excl. VVT models)