Krumtaphus S&S natur Early Shovelhead 66-69
S&S Super Stock generatorkrumtaphus
Læs mere
- Fremstillet i 356-T6 aluminium med naturlig finish
- STD-boring til 3.4375" cylindre
- Gevindskåret 1/4"-20 til transmissionsdæksel, oliepumpe, løfterstyr og tænding
- Boret til 5/16" monteringsbolte til generator
- Frigang til op til og med 5" slaglængde uden ekstra bearbejdning
- Svinghjulsskraber tilpasset 8-1/2" svinghjulsdiameter
- Linjehonede lejebaner og præcisionsbearbejdet krumtaphusventilationsrum
- Leveres med bolte, tapbolte, Timken-lejer, tætninger, bøsninger og propper
- Fremstillet i USA
Til brug med primærhus i aluminium (1965-modeller bruger 1965 indre primær i legering). Tandhjulskit til generatorkrumtaphus og aksler købes separat. Modeller fra 1963–1965 med udvendige olieslanger skal bruge olieport bag løfterblokken eller i transmissionsdækslet samt specialtilpassede olieslanger.
Passer til: Tidlig Shovelhead 66-69
| Färg | Silver |
| Material | Aluminum |
| Produkt-typ | Engine Case |
| Tillverkarens Art. Nr. | 31-0010 |
Super Stock Generator Engine Case
- Includes crankcase bolts, washers and nuts, cylinder mounting studs, timing hole plug, magnetic drain plug, assorted breather and oil line fittings, top end oil screen spring and plug, sprocket shaft Timken bearing assembly, oil seal, pinion shaft main bearing race, cam needle bearing assembly, oil pump shaft bushings and installation instructions
- Bearing races are all line honed and breather cavity is precision machined to optimize breather timing for maximum oil scavenging
- Machined for 3.4375" cylinders and tapped 1/4"-20 for gear covers, oil pump, tappet guides, timer and timer advance
- Uses Timken style sprocket shaft bearings
- '65 models use '65 alloy inner primary
- Drilled for 5/16" generator mounting bolts
- Made in the USA
- Generator crankcase gear kit (includes circuit breaker drive gear, idler gear, circuit breaker gear and shims) and shafts must be purchased separately.
- '63-'65 models with outiside oil lines must use oil port to the rear of the tappet block or oil port in gear cover and use custom oil lines.
- 65-69 crankcase assembly, STD bore. Natural
- For use with an aluminum primary housing
- S&S Superstock crankcases, made from 356-T6 aluminum, are much stronger than the OEM case
- OEM cases can/may break in high performance or even stock applications, like more than a few of us found out the hard way
- These S&S Superstock cases can be used for both stock replacement and racing applications
- Important to the engine builder are the substantial savings in labor when using S&S cases
- Additional parts that are supplied include Timken sprocket shaft bearings, cylinder studs, nickel plated case bolts, crankcase fittings, oil pressure sensor, timing & magnetic crankcase drain plugs and a special S&S design alternator stator plug clamp screw
- The flywheel scrapers are machined to match the original 8-1/2" diameter flywheels
- S&S cases are clearanced up to and including 5", no additional clearancing for strokers will be necessary
- Note: In any and all applications the technician must be able to judge components for their suitability in combination with the other engine components, prior to installation
- It is of importance that a knowledgeable mechanic will install & make adjustments as required
Fits: 66-69 Early Shovelhead; 1965 Panhead with aluminum primary (NU)