Ventillyftare Feuling Race Series kort slag .842″ M8 H-D 17-upp
Feuling Race Series hydrauliska lyftare med kort fjädringsväg
Lue lisää
- Kort slaglängd med 0.115" total fjädringsväg jämfört med 0.200" på standardlyftare
- Minskar ventilsläpp och vibrationer i ventilsystemet för ökat varvtal och tyst gång
- Kropp tillverkad i stål med lång kallsmidd och precisionsslipad kolv
- Precisionsslipat nållager med axel i högkromat stål för minimal friktion och lång livslängd
- Snabbreagerande backventil av skivtyp med högt flöde
- Kompatibel med Feulings oljepumpar i HP+- och Race Series-serierna
- Standard ytterdiameter (STD OD)
- Tillverkade i USA och säljs i set om 4
Lyftarna ska ställas in med 0.065"–0.070" förspänning och rekommenderas för motorer med över 185 lb (84 kg) ventilfjäder fjädersäte, tryck. Feuling rekommenderar att varje lyftare pumpas upp för hand innan montering samt att en oljepump med hög volym används.
Passar: H-D 17-upp
| Produkt-typ | Lifter |
| Tillverkarens Art. Nr. | 4017ST |
Race Series Short-Travel Hydraulic Lifters
- New revolutionary design with 0.115" of total travel vs. a full travel lifter with 0.200"
- Increases RPM by decreasing valve float and valve-train harmonics while maintaining a quiet engine
- Travel reduction reduces the amount of oil that is required to fill the inside of the lifter which reduces oil aeration inside the lifter on steep, fast action high lift camshaft lobes
- When oil aeration is present inside the lifter, the pushrod seat drops when the lifter rolls onto the front cam lobe ramp after squeezing the aeration down thus creating a noisy poor performing lifter
- Short travel lifters should be set with 0.065" - 0.070" of pre-load and with the normal engine growth from heat will put the operating lifter pre load at or around half travel
- Machined from a steel body and designed to exceed the needs of large lift camshafts and higher valve spring pressures with a slower bleed down rate
- Compatible with either Feuling HP+ or Race Series oil pumps and are designed for use with both street and strip engines
- Maintain proper oil flow to the top end, increase engine RPM, valve-train stability, decreasing valve float promoting maximum valve lift
- Precision ground needle roller bearing with high chromium steel axle for long life and minimal friction
- High-flow disc-style quick-reacting check valve for better reaction at higher RPM
- Spin-Tron dyno developed and track proven
- Made in the USA
- Feuling recommends pumping up each lifter by hand prior to installation, to remove all air and provide a fully pumped up lifter. Use of a thin weight oil like ATF in a squirt can works well.
- Feuling recommends Race Series lifters for engines running higher than 185 lb (84 kg) valve spring seat pressure.
- Feuling recommends the use of a high volume oil pump which will result in quieter, better performing lifters.
- Race Series tappet set. Short travel. STD OD
- Comes with shorter .115" of travel
- Better Performance!
- Stock replacement to full out Drag race
- Cold forged extra long piston, precision ground and fitted for controlled leak down and pump up
- Available in oversized diameters – Case Savers!, Ideal side clearance is 0.001"
- Sold in sets of 4
- See Feuling tool 588060 to check lifter bore diameters
Fits: 99-17 (NU) Twin Cam; 17-26 M8; 00-22 (NU) XL; 08-12 (NU) XR1200; 00-10 (NU) Buell XB