Oljepump Feuling Parts M-Eight Water Cooled H-D 17-upp
Feuling Parts högtrycks- och högvolymsoljepump för Milwaukee-Eight
Lue lisää
- Tillverkad i 6061 billet-aluminium med natur-finish
- 2.250" (5,72 cm) gerotor-kugghjul i krommolybdenstål med högt flöde
- 68 % mer oljevolym till vevaxel och vevstakslager samt 42 % mer returvolym
- För M-Eight Twin-Cooled: 30 % mer tryckvolym och 53 % mer returvolym än original
- För M-Eight oljekylda: 27 % mer tryck- och returvolym än original
- Magneter samlar upp stålpartiklar och skyddar kugghjul och övertrycksventil
- Bänktestad med ventil tätad till minst 30 psi (2,06 bar) och full öppning vid 55–60 psi (3,79–4,13 bar)
- Tillverkad i USA
Kräver montering tillsammans med Feuling High Flow kamplatta (artikelnr 0932-0192 / 588056). Notera att M-Eight har oljeupptagningen på motorns högra sida, tomgång på sidostödet gör att vevhuset fylls med olja och ger felaktig nivå i tanken.
Passar: H-D 17-upp
| Produkt-typ | Pump |
| Tillverkarens Art. Nr. | 7019 |
High Pressure / High Volume Oil Pump for M-Eight
- Increased oil volume from the larger gears and properly sized passages along with the pressure relief valve seat and seal from these oil pumps is essential for proper oiling system function
- Eliminate common pressure and scavenge issues associated with the factory oil pumps
- Precision-machined pressure relief valve and bore
- Every pump is bench tested, the relief valve is seated and sealed to a minimum of 30 psi with full pop-off at 55-60 psi
- Feuling M-Eight oil pumps have the groove machined on the back cover to accept the factory crank bearing seal
- When matched to a Feuling cam plate, pumps reduce engine and oil temperatures, increase oil pressure volume, and scavenge volume on the return side to reduce build up of oil in the crankcase
- Increase oil flow in and out of the engine with corrected tolerances, oil passages and larger geroter gears
- High-flow 2.250" Chrome Moly gerotor gears
- 42% more scavenge volume with matched passages, port sizing and holes to the engine case
- 68% more oil volume to the crankshaft and connecting rod bearing
- Magnet to help protect gears and pressure relief valve
- More horsepower and torque to the rear wheel
- M-Eight Twin-Cooled motors have 30% more pressure gear volume over stock and 53% more scavenge gear volume over stock
- M-Eight oil-cooled motors have 27% more pressure and scavenge gear volume over stock
- Billet 6061 aluminum with natural finish
- Increases oil pressure
- Increased kidney passage volume
- Eliminates blow by and wet sumping
- Cooler oil & engine temperatures
- Made in the USA
- Increased and optimized scavenge port holes and galleys requires being matched to a Feuling High Flow cam plate PART #0932-0192.
- EU: Every pump is bench tested, the relief valve is seated and sealed to a minimum of 2,06 bar with full pop-off at 3,79 bar - 4,13 bar
- M-Eight oil pick up port is on the right side of the engine. Letting the bike idle or warm up on the kickstand will naturally fill the engine case and skew the oil level in the tank.
- EU: High-flow 5,72 cm Chrome Moly gerotor gears
- Magnets catch small steel particles and help prevent oil pump damage
- Each pump is bench tested before it is shipped
- Note: When running the Feuling HP+ oil pump you must use Feuling 588056 high flow cam plate
Fits: 17-26 M8 Touring. (Water cooled models only)