Kamaxelsats Feuling O 124″ 38.5 kort M8 '17-'24 Except VVT OIL

38 000 kr

Feuling Race Series Kamaxelsats med korta hydraullyftare
Läs mer

09251418 Feuling
  • Satsen innehåller oljepump, kamplatta, Reaper 538-kamaxel, korta hydraullyftare, stötstänger, kamlager, vipparmsbultar/muttrar, packningar, o-ringar och ARP-fästelement
  • Oljepump tillverkad i billet 7075-aluminium, 50 % hårdare och starkare än original med integrerade magneter
  • Short travel hydraullyftare med 0.115" total slaglängd minskar ventilsläpp och vibrationer
  • Ökar oljetrycket med 10–30 psi och ger 68 % mer oljevolym till vevaxel och vevstakslager
  • Ger 15°–25° lägre motortemperatur och 15°–30° lägre oljetemperatur
  • Aggressiv Reaper 538-kamaxelprofil med lyft på .538" (insug) och .542" (avgas)
  • Tillverkad i USA

Kräver ventilfjädrar för högt lyft och hög belastning. Passar inte '23-'26-modeller med 121" VVT-motor.

Passar: M8 '17-'24 utom VVT OLJE-

Race Series Camchest Kit with Short Travel Lifters

  • Billet 7075 aluminum oil pump, which is 50% harder and stronger than the factory pump, holding tighter tolerances under temperature
  • Short travel hydraulic lifters have 0.115" of total travel and will increase rpm by decreasing valve float and valve-train harmonics while maintaining a quiet engine
  • Deeper scavenge kidney ports over the HP+ series for even more scavenge flow volume
  • 30% more pressure gear volume over stock for M-Eight Twin-Cooled motors
  • 53% more scavenge gear volume over stock for M-Eight Twin-Cooled motors
  • 27% more pressure and scavenge gear volume over stock for M-Eight Oil-Cooled motors
  • 42% more scavenge volume with port sizing, matched passages and holes to the engine case for M-Eight Twin-Cooled motors and M-Eight Oil-Cooled motors
  • 68% more oil volume to the crankshaft and connecting rod bearing for M-Eight Twin-Cooled motors and M-Eight Oil-Cooled motors
  • 15°-25° cooler engine temperatures for M-Eight Twin-Cooled motors and M-Eight Oil-Cooled motors
  • 15°-30° cooler oil temperatures for M-Eight Twin-Cooled motors and M-Eight Oil-Cooled motors
  • 10-30 more psi of oil pressure for M-Eight Twin-Cooled motors and M-Eight Oil-Cooled motors
  • Increases oil pressure, scavenge volume and engine oil flow
  • Reduces wet sumping, blowby and oily air cleaners
  • Magnets in oil pump to help protect gears and pressure relief valve
  • Test results show 2 hp gain and 2 ft/lb of TQ gain to the rear wheel on M-Eight
  • Feuling test results show a 50% reduction of engine sump oil level
  • Kit includes: Race Series high volume oil pump, High Flow billet camplate, Reaper Series camshaft, Race Series short hydraulic roller lifters, one piece pushrods, Timken/ Koyo cam bearings, rocker arm studs/ nuts, gaskets, O-rings, ARP cam/ crank fasteners, washers, moly paste and Loctite
  • Made in the USA
  • Not for '23-'26 models with 121" VVT motor.
  • FEULING M8 OIL COOLED camchest kits include all necessary components from top to bottom of the camchest conveniently packaged under 1 part #
  • These combination kits not only ensure each individual part is designed to work and function together but to do so in total harmony
  • These camchest kits take the guess work out of the ordering process and guarantees the engine builder maximum reliability, peak performance and the coolest engine and oil temperatures obtainable
  • Quieter and smoother engine operation
  • Due to the mass call volume & inquires with requests for the M8 oil pump back cover O-ring/seal groove, we’ve added the groove! (5/11/21)
  • Although Feulings in house testing on healthy engines did not show a benefit
  • The O-ring may have potential benefits in certain circumstances such as engines with higher cylinder leak down, poor subseal O-ring seal, raised sump hole & or sump plug (see M8 PRO TIP below) & looser lifter to lifter bore clearances
  • Aggressive camshaft with a "nasty" sound
  • This camshaft revs up fast and pulls hard in engines with big bore cylinders, modified cylinder heads, inake, compression and exhaust
  • The REAPER 538 grind will shine in 124" and larger cubic inch engines with added compression ratio
  • Ported cylinder heads are not required but will complement the cam and add even more pulling power throughout the range
  • The stock throttle body produces an excellent powerband and use of a high flow throttle body will increase peak power numbers
  • A high flow exhaust system and air cleaner is highly recommended for optimal performance
  • FEULING recommends matching this cam with our RACE SERIES oiling system
  • SE cylinder heads have high lift valvesprings but will need to be verified
  • Heavy Duty one piece pushrods are also highly recommended see #4087
  • 5,975
  • Grind: 538 ..................Valve Lift Open Close Duration @ 50" lift @ TDC Lobe Centerline Intake .538 20.5 BTDC 38.5 ABDC 239 .180 99 Exhaust .542 48 BBDC 18 ATDC 246 .157 105 Overlap: 38 *Cam specs measured in the engine on the lifter @ 0.050" using a 1.61 rocker arm ratio DISCLAIMER: NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VECHICLE Feuling dOEs not recommend tuning beyond stock emissions standards
  • RACE SERIES hydraulic lifters have a full .200" of total travel designed with a slower bleed down rate to handle heavy valve spring pressures, increase engine RPM before valve float and feature increased roller clearance for steep ramped camshafts and clearance for the M8 front exhaust camshaft lobe flange
  • OIL LEVEL NOTE
  • DO NOT OVERFILL OIL TANK It is important to get the correct hot oil level in your bike
  • Letting the bike idle or warm up on the kickstand will naturally fill the engine case and skew the oil level in the tank
  • We recommend the following steps to achieve proper oil level: 1
  • Check cold oil level
  • Ride the bike until operating temperature is reached
  • 3
  • Shut the bike off while still in the upright position. (This insures an accurate reading) 4
  • Add or remove oil as needed
  • Note: Special Order Product only
  • To order please contact your MCS sales representative

Requires high-lift/high-load valve springs. Requires high lift valve springs. Includes: • Race Series High Volume Oil Pump • High Flow Billet Camplate • Reaper Series 538 Camshaft • Race Series Short Travel Lifters • One Piece Pushrods • Timken/Koyo Cam Bearing • Rocker Arm Studs and Nuts • Gaskets • O-Rings • ARP Cam/Crank Fasteners • Washers • Moly Lube • Loctite

Fits: M8 '17-'24 Except VVT OIL cooled, Chain Drive, Includes 538 Reaper Camshafts #1351, Cam Install kit #2030, RACE SERIES Short Travel Lifters #4017ST, one piece pushrods #4088, RACE SERIES oil pump #7020, HIGH FLOW camplate #8017, and ARP Rocker studs and nuts, Camplate/Oil Pump Fasteners.