Tätningar ventilstyrning Kibblewhite 48-77 H-D 48-84 (4-pack)

200 kr

Tätningssats för ventilstyrningar i PTFE från Kibblewhite
Läs mer

09260792 Kibblewhite
  • Tillverkade i PTFE med tillsatser som håller materialet stabilt och minskar friktionen
  • Behåller sina mekaniska egenskaper vid temperaturer upp till 500° F
  • Design med dubbla fjädrar ger kontinuerlig spänning mot ventilstyrning och ventilspindel
  • Kompatibel med ventilstyrningar av OEM-stil utan krav på bearbetning
  • För insug och avgas
  • Tillverkade i USA

För Shovelhead används de med 0.565" styrningar. Monteringstips: PTFE-tätningar kräver en annan monteringsteknik än vanliga tätningar då de är ca 0.020" (0.50mm) mindre än spindel och styrning, tryck inte direkt på tätningens topp utan använd en 12-punkts 12 mm hylsa mot kanten för att pressa den på plats. Installationsskydd i mylar rekommenderas vid montering över ventilen (501823 grön 5/16" / 0.3125", 501824 gul 11/32" / 0.34375", 501825 3/8" / 0.375").

Passar: H-D 48-84

Produkt-typ Seal
Material PTFE
Tillverkarens Art. Nr. 71002-4

Solid PC Valve Guide Seals

  • Manufactured from PTFE
  • PTFE is known to retain its mecahnical properties at temperatures as high as 500° F
  • Fillers have been added to keep the material stable and to reduce friction
  • Twin spring design provides continous tension on the valve guide and the stem of the valve
  • Made in the USA
  • KPMI, int/exh. valve guide seal kit. PTFE
  • Manufactured with PTFE lining
  • Kibblewhite Precision Machining valve guide seals are compatible with OEM style valve guides
  • No machining required
  • Installation note: Valve guides made of PTFE require another fitment technique than 'regular' or non-PTFE valve guides, this is due to the PTFE material
  • They are typically 0.020” (0.50mm) smaller than the valve stem and guide top they’re designed to fit
  • The guide top should have a decent chamfer
  • The valve stem should have a decent chamfer, but a mylar seal installation protector / installation capsule (501823 green 5/16" / 0.3125", 501824 Yellow 11/32" / 0.34375", 501825 3/8" / 0.375") is advised for easier installation over the valve stem
  • You have to kind of roll the seal around the valve tip while exerting downward pressure to get it started
  • Don't push directly on the very top of the seal to get it on to the guide, you’ll collapse the sealing area and tear the seal
  • A 12 point 12mm socket catches the shoulder of the guide pretty well and can be used to push the seal on to the guide until it just bottoms out
  • The choker wire around sealing area and the band around the area that fits the guide, combined with the hardness of the material itself makes the seal a tight fit and little harder to install than regular Viton seals
  • PTFE material does not have 'memory' and therefore is subject to creep
  • This creep allows the seal to conform to mating surfaces
  • Because of the ‘creep’ characteristic, the seal relaxes a bit after installation, and doesn’t drag on the valve stem as hard as it does during installation

For Shovelhead use with 0.565" guides.

Fits: 48-65 Panhead; 66-E79 Shovelhead (NU)