Kamaxelsats S&S 585G Gear Drive H-D 99-06

15 000 kr

S&S 585G kamaxelsats med kuggdrivning
Läs mer

20072585 S&S
  • Kuggdriven kamaxelsats med .585" ventillyft
  • Ger mer exakt ventilstyrning utan kedjeglapp och slitande kedjespännare
  • Konstruktion som vänder bakre kamaxelns rotationsriktning för ökat frigångsutrymme mellan kamloberna
  • Effektområde: 3500–6000 rpm (88"–103") och 2500–5500 rpm för större motorer
  • Satsen innehåller kamaxlar, innerdrev, ytterdrev, inre och yttre lager, packning samt instruktioner
  • Tillverkad i USA

Kräver justerbara stötstänger samt kontroll av ventil-till-kolv- och ventil-till-ventil-frigång vid montering. Material måste avlägsnas från insidan av transmissionskåpan för frigång. Montering kräver hydraulisk press och professionella verktyg.

Passar: H-D 99-06

Produkt-typ Cam Kit
Tillverkarens Art. Nr. 33-5179

585G Gear Drive Camshaft Kit

  • Designed for 88/96/103/110 cubic-inch engines with compression ratios from 10.0:1 to 10.5:1
  • Reverses the rear cam's direction of rotation, providing additional operating clearance between cam lobes making higher cam lifts possible
  • Increases valve timing accuracy by eliminating chain lash and loosely fit stock chain drive
  • Material must be removed from inner surface of the stock gear cover to install
  • 3500-6000 rpm for 88" to 103" engines and 2500-5500 rpm for larger engines
  • A hydraulic press and other professional level tool are required for installation
  • S&S recommends that adjustable pushrod/cover get be used
  • Cam bearings and gaskets must be replaced when installing new cams
  • Kit includes camshafts, inner gears, outer gears, inner bearings, outer bearings, gasket and instructions
  • Installer must check coil bind, valve to valve clearance and valve to piston clearance.
  • Due to the inherent characteristics of gear drives, more valve train noise may occur.
  • Made in the USA
  • 585" valve lift
  • Bolt-in 88" to 106" with 9.7:1 to 10.5 CR and 106" to 124" with 9:1 to 10:1 CR
  • The gear drive system is in fact a revolutionary different and much more reliable construction
  • Especially in high lift/performance applications, when compared with the OEM chain-drive design
  • A gear driven camshaft is stronger and will not give any of the mechanical problems connected with the OEM chain driven camshafts
  • The only downside of gear drive is that you may experience a slight increase in mechanical sound, this is why OEM is using a chain
  • It has no other mechanical advantages whatsoever
  • Since the chain guides and tensioner are eliminated there is no longer the possibility for these parts to fail and damage other engine parts
  • Note: With the exception of the 475G and 510G cam, adjustable pushrods (like MCS 503573) are required to compensate for the smaller camshaft base circle of these cams
  • Note: Using .625", .635", .640" and .675" lift cams will require crankcase clearancing
  • Note: OEM beehive valve springs of 04-17 Dyna; 04-17 Softail and 04-16 Touring models will acommodate valve lifts up to 590" valve lift and, 160 lb. of valve seat force, up to 6200RPM
  • Running higher than 6200 RPM or lifts greater than 590" will require performance valve springs

'99-'04 models require high-lift springs and adjustable pushrods.

Fits: 99-06 Twin Cam (Excl. 2006 Dyna) with stock non-hydraulic chain tensioners (NU)


Liknande produkter

Kamaxelsats S&S M8 465G svart Touring 17-24, Trike 21
Svänghjul S&S V-Series Motor H-D 84-99
Svänghjul S&S Taper 4.375 H-D 17-23
Kamaxel S&S 465 17-19 M8 H-D 17-upp 558693k-ed4525c4
Fjädersats ventil S&S Sidewinder 0.650 H-D 86-22 531869k-6a8768cb