Tændingsmodul Dynatek Dyna 2000HD enkelt dobbelt Softail 96-99
Dynatek 2000-HDE PC-programmerbart digitalt tændingsmodul
Læs mere
- Plug-in-opgradering, der monteres eksternt med 8-polet Deutsch-stik
- Mikrocomputerstyret tænding til både single-fire og dual-fire
- 4 forudindstillede tændingskurver og 4 omdrejningstrin fra 6000 til 7500 rpm
- Hurtigkurve, der simulerer en mekanisk tændingsforstiller til trimmede motorer
- PC-programmering af kurver ved fuld og delvis gas, omdrejningsbegrænsning, startomdrejninger og offset for bagerste cylinder
- Mulighed for vakuumkompensering via VOES samt tændingsretardering med 5°, 7° eller 10°
- Separat udgang til omdrejningstæller og diagnostisk LED-indikator på bagsiden
- Fremstillet i USA
Passer ikke til modeller med brændstofindsprøjtning. HDE-systemer er ikke kompatible med Dyna S-systemer (brug kun HD1/HD2-systemer). Tændkabler af kulfibertype skal bruges til radioafstøjning, tændkabler i kobber må ikke bruges, da forstyrrelser ved tændrørene kan forårsage fejl i tændingen (originale kabler fra Harley-Davidson fungerer normalt).
Passer til: Softail 96-99
| Produkt-typ | Module |
| Tillverkarens Art. Nr. | DD2000-HD1E8P |
-
Hämta21010045_DD2000-HD1E8P.pdf218.59 KB
2000-HDE PC-Programmable Digital Ignition Module
- A plug-in upgrade to the electronic advance ignition found on late model Harleys, these ignitions are micro-computer controlled, generating extremely accurate control over the entire ignition process
- Allow riders to tailor the advance curve and rev limiter to the specific needs of their particular engine; four built-in advance curves cover the needs of stock to highly modified engines over a variety of operating conditions; four independent rev limiter choices from 6000 to 7500 rpm set the exact protection level needed
- PC programmability allows you to define a wide-open and part-throttle curve, rev limits, dead-cranking revs and rear cylinder offset
- A separate tach output wire allows clean tach operation during rev limiting and when in single-fire mode
- A diagnostic LED indicator is included on the back of the control module to assist trouble shooting and static timing
- Made in the USA
- IMPORTANT: On any electronic advance ignition such as the Dyna 2000-HD1 or the stock Harley ignition, you must use carbon fiber-type suppression spark plug wires to reduce radio frequency interference. Use of copper wires may cause malfunction of the ignition due to severe electrical noise generated at the spark plugs. The original wire supplied by Harley-Davidson should be okay.
- Not for fuel-injected models.
- HDE systems are not compatible with Dyna "S" systems. Use HD1/HD2 systems only.
- 8-pin Deutsch connector
- Used in combination with the OEM HD ignition system
- The system must mount externally and lets you control advance curves by using 4 preset modes and the R.P.M. limiter lets you choose from 4 R.P.M. limits from 6000 to 7500
Comes with 8-pin connectors; operates in single-fire or dual-fire modes Offer a quick curve which simulates a mechanical advancer for hot rod motors; option to use vacuum advance compensation via a VOES switch and retard mode, which allows selection of ignition retard of 5°, 7° or 10° upon activation of a retard input
Fits: 96-99 Softail; 96-98 Dyna; 94-98 FLT/Touring; 94-97 XL Sportster (NU)