Oliesystem Feuling HP M8. Oliekølede modeller 17-25
Komplet HP+ oliesystem med oliepumpe og knaststøtteplade
Læs mere
- Fremstillet i USA
- Knaststøtteplade i billet 7075-aluminium, 50 % hårdere og stærkere end original
- Højvolumen-oliepumpe i billet 6061-aluminium
- 27 % mere tryk- og returtandhjulsvolumen sammenlignet med original
- 42 % mere returvolumen samt 68 % mere oliemængde til krumtapaksel og plejlstangslejer
- Giver 10–30 psi højere olietryk samt sænker motor- og olietemperatur med 15°–30°
- Inkluderer hydrauliske HP+ rulleløftere, knastlejer, monteringssæt, bolte, skiver og pakninger
- Kompatibel med både kædedrift og tandhjulsdrevne knastaksler
Beregnet til oliekølede Milwaukee-Eight-motorer. Spillet mellem forreste udstødningsløfter og knastakselflange skal kontrolleres ved montering. Overfyld ikke olietanken, kontrollér altid oliestanden med varm motor i oprejst position, da tomgangskørsel på sidestøtten kan give et misvisende niveau.
Passer til: M8. Oliekølede modeller 17-25
| Färg | Red |
| Produkt-typ | Oil System |
| Tillverkarens Art. Nr. | 7096 |
HP+ Oil System Packs for M8
- Includes FUELING High Flow billet camplate made from 7075 aluminum which is 50% harder and stronger than the factory or FUELING OE+ camplates
- Increases oil flow and volume by enlarging the oil pump reservoirs and critical oil passages including matching the oil portholes throughout the camplate to the portholes in the engine case which increases engine oil flow to the lifters, piston cooling jets, crankshaft and rod bearings
- FUELING oil pumps are bench tested, the relief valve is seated and sealed to a minimum of 30 psi with full pop off at 55-60 psi
- Increased oil volume from the larger gears and properly sized passages along with the pressure relief valve seat and seal from these oil pumps is essential for proper oiling system function
- FUELING oil pump and camplate combination eliminate common pressure and scavenge issues associated with the factory oiling systems
- FUELING M-Eight oil pumps have the groove machined on the back cover to accept the factory crank bearing seal
- Quieter and smoother engine operation
- Increase oil pressure, scavenge volume and engine oil flow
- 42% more scavenge volume with port sizing, matched passages and holes to the engine case
- 68% more oil volume to the crankshaft and connecting rod bearing
- Engine temperatures run 15°-25° cooler
- Oil temperatures run 15°-30° cooler
- 10-30 lbs more psi of oil pressure
- Reduces wet sumping, blowby and oily air cleaners
- Test results show 2 HP gain and 2 ft/lbs of torque gain to the rear wheel on M-Eight
- Includes billet 6061 aluminum high volume oil pump, High Flow camplate, HP+ Hydraulic roller lifters, cam installation kit, cam bearing, cam/crank bolts and washers, engine and fastener assembly lube
- Made in the USA
- Optional FUELING X ARP bolt kit available for the High Flow camplate PART #0932-0192 and HP+ or RS oil pump combo. See PART #2401-0993, optional ARP oil pump bolts do not use washers.
- Optional FUELING X ARP oil pump/camplate bolt kit available PART #2401-0993.
- FUELING test results show as much as 50% reduction of engine sump oil level.
- M-Eight engines must check clearance on front exhaust lifter to camshaft flange fit.
- Compatible with chain and gear drive camshafts
- Complete Feuling kit with the HP+ oil pump, the special high flow cam support plate a set of HP+ series hydraulic lifters and a quick cam gasket set
- FEULING OIL COOLED oiling system kits combine all the needed components to finish your M8 engine's oiling system under 1 part number, available in HP+ or RACE SERIES kits
- Due to the mass call volume & inquires with requests for the M8 oil pump back cover O-ring/seal groove, we’ve added the groove! (5/11/21)
- Although Feuling's in house testing on healthy engines did not show a benefit
- OIL LEVEL NOTE
- DO NOT OVERFILL OIL TANK It is important to get the correct hot oil level in your bike
- Feuling recommends running the oil level 90%-99% full when hot
- Note: The M8 oil pick up port is on the right side of the engine
- Letting the bike idle or warm up on the kickstand will naturally fill the engine case and skew the oil level in the tank
- We recommend the following steps to achieve proper oil level: 1
- Ride the bike until operating temperature is reached
- 3
- Shut the bike off while still in the upright position. (This insures an accurate reading) 4
- Add or remove oil as needed
27% more pressure and scavenge gear volume over stock.
Fits: 17-25 M8. Oil cooled models
Lignende produkter
Feuling
Oliesystem Feuling Race Series tandhjuls- eller kædedrift M8 oliekølet 17-25
09320199
15 352,5 DKK