Krumtaphus S&S 3-5/8" natur Knucklehead med 3-5/8 big bore
S&S Superstock krumtaphus i naturfinish med 3-5/8" cylinderboring
Læs mere
- Fremstillet i 356-T6 aluminium for væsentligt højere styrke end original
- Egnet til både standard erstatning og racingapplikationer
- Leveres med formonterede Timken-lejebaner til transmissionsaksel, knastnållejer samt indpresset og honet lejebane til pinionaksel
- Maskinbearbejdede krumtapskrabere tilpasset svinghjul med originalens 8-1/2" diameter
- Portet krumtaphusventilation for maksimal oliereturkapacitet
- Frigang bearbejdet til slaglængder op til og med 5"
- Inkluderer Timken-lejer til transmissionsaksel, gevindbolte til cylinder, fornikkelede krumtaphusbolte, krumtaphusnipler, olietryksensor, propper og statorpropskrue
- Naturfinish
Passer ikke med OEM-svinghjul, pinionaksel eller transmissionsaksel til 36-54, da alle S&S-krumtaphuse bruger Timken-lejer af senere type (1955 og senere). Til 36-55 Big Twin kan 58-81 pinionaksel og 55-64 splinet transmissionsaksel bruges sammen med S&S-svinghjul med 6° konus og kilespor.
Passer til: Knucklehead med 3-5/8 big bore
36-47 crankcase assembly, 3-5/8" bore. Natural
- S&S Superstock crankcases, made from 356-T6 aluminum, are much stronger than the OEM case
- OEM cases can/may break in high performance or even stock applications, like more than a few of us found out the hard way
- These S&S Superstock cases can be used for both stock replacement and racing applications
- Important to the engine builder are the substantial savings in labor when using S&S cases
- These cases come 'set up' with sprocket shaft Timken main bearing races and cam needle bearings installed and pinion shaft main bearing race pressed in and line-honed
- Additional parts that are supplied include Timken sprocket shaft bearings, cylinder studs, nickel plated case bolts, crankcase fittings, oil pressure sensor, timing & magnetic crankcase drain plugs and a special S&S design alternator stator plug clamp screw
- The flywheel scrapers are machined to match the original 8-1/2" diameter flywheels
- S&S cases maximize crankcase oil scavenging efficiency by using a 'ported' design breather passageway
- S&S cases are clearanced up to and including 5", no additional clearancing for strokers will be necessary
- Note: S&S crankcases for 36-54 Knuckle and Panhead models will not take OEM flywheels, pinion or sprocket shaft since late style (1955-up) Timken bearings are used in all S&S cases
- 55-up shafts will not fit 36-54 OEM flywheels, S&S does not recommend machining 36-54 flywheels to take 55-up shafts
- For all 36-55 B.T. applications 58-81 (MCS 512404) pinion & 55-64 (MCS 512401) splined sprocket shafts can be used with S&S flywheels, which all have a 6° shaft taper with keyway
- Note: In any and all applications the technician must be able to judge components for their suitability in combination with the other engine components, prior to installation
- It is of importance that a knowledgeable mechanic will install & make adjustments as required
Fits: 36-47 Knucklehead with 3-5/8 big bore cylinders (NU)