Kamaxelsats S&S 551 Easy Start Gear-driven 551GE H-D 99-06

16 930 kr

S&S 551 Easy Start kugghjulsdriven kamaxelsats
Läs mer

09250453 S&S
  • Easy Start-funktion underlättar start genom att lyfta avgasventilen via en fjäderbelastad lob som dras in centrifugalt vid start
  • Optimerad för 88"/96"/103" till 106" Touring-modeller med slip-on ljuddämpare och 9.0:1 till 9.0:9 i kompression
  • Ger avsevärt bättre vridmoment i låg- och mellanregistret, starkast från tomgång till 4000 rpm
  • .550" ventillyft
  • Kugghjulsdrivning (IOG) med inre och yttre drev (4-kuggars sats)
  • Innehåller kamaxlar, kåppackning, lager, låsring, o-ring, gänglåsning, monteringsdetaljer och instruktioner
  • Kan användas med original stötstänger, lyftare och fjädrar om inget annat anges
  • Tillverkad i USA

Rekommenderas inte för kompressionsförhållanden på 10.0:1 eller högre, och passar inte modeller med OEM dekompressionsventil eller kickstart. För 99-06 Twin Cam krävs kontroll av frigång och eventuellt ventilfjädrar för högre lyft. Montering kräver kontroll av ventilfjädrarnas bottning samt frigång mellan ventiler och mellan ventil och kolv, justera tomgång till 1000–1100 rpm för att undvika klickljud under 900 rpm.

Passar: H-D 99-06

Produkt-typ Cam Kit
Tillverkarens Art. Nr. 106-5442

551 Easy Start Camshaft Kit

  • Allows for easy start by initially reducing crank compression, but once the engine starts and rpm increases, the compression release lobe is centrifugally retracted and the engine runs normally, with full compression, and without any loss in performance
  • Optimized for 88"/96"/103" to 106" Touring bike with slip-on mufflers and 9.0:1 to 9.0:9 compression with stock starter
  • Bolt-in for stock or mildly modified Touring models
  • Greatly improves low-end and midrange torque
  • Strongest from idle to 4000 rpm
  • Includes camshafts, gearcover gasket, bearings, retaining ring, o-ring, threat lock and instructions
  • Made in the USA
  • Not recommended for compression ratios of 10.0:1 or greater.
  • Installer must check coil bind, valve-to-valve clearance and valve-to-piston clearance.
  • Not for models with OEM compression releases.
  • Can be used with stock pushrods, lifters, and springs (unless noted).
  • 550" valve lift
  • IOG = gear drive cams with Inner & Outer drive Gears
  • Complete kit with installation hardware, bearings and gasket
  • Easy Start Cams make starting easier by reducing the build-up of cranking pressure in the cylinders during starting
  • This is done by lifting the exhaust valve slightly of its seat, with a spring loaded compression release lobe inside the camshaft
  • After starting the compression release lobe is retracted by centrifugal force
  • The only difference is during starting since you will now be able to electric start your Big Inch engine effortless, without the use of big batteries and/or starter motors
  • A stock starter and battery is enough
  • When the engine is running the camshafts function as regular cams, without any loss in power, torque or anything else
  • They are separately available as replacement from S&S for this kit as 503566
  • Note: No Easy Start Cam grind is bolt-in for these 99-06 Twin Cam models
  • All will / may require clearancing and require high lift valve springs
  • Note: Not compatible with kickstart models
  • Note: Camshafts made before Jan
  • 2010 will require adjustable pushrods
  • Note: Below 900 RPM you may hear a clicking sound
  • Adjust idle speed to 1000-1100 RPM

Includes 4-gear set. Due to the inherent characterics of gear drives, there may be more valve train noise.

Fits: 99-06 Twin Cam (Excl. 2006 Dyna) (NU)