Knastaksel S&S Easy Start 551 Softail 07-17

5 223,3 DKK

S&S 551 Easy Start knastakselsæt med kædedrift
Læs mere

09250443 S&S
  • Easy Start-funktion gør elstart lettere ved at reducere startkompressionen via en fjederbelastet knast på udstødningsventilen
  • Knasten trækkes tilbage centrifugalt, når motoren er startet, for fuld kompression og ydelse
  • Bolt-in-knastaksel optimeret til 88"/96"/103" til 106" Touring med slip-on lyddæmpere og 9.0:1 til 9.0:9 i kompression
  • Forbedrer drejningsmomentet i lav- og mellemregisteret, stærkest fra tomgang til 4000 rpm
  • .550" ventilløft
  • Kan bruges med originale stødstænger, løftere og fjedre
  • Indeholder knastaksler, pakning til transmissionsdæksel, lejer, låsering, O-ring, gevindlåsning og monteringsvejledning
  • Fremstillet i USA

Anbefales ikke til kompressionsforhold på 10.0:1 eller højere og passer ikke til modeller med OEM-dekompressionsventiler eller kickstart. Montøren skal kontrollere, at ventilfjedrene ikke går på blok (coil bind), samt frigang mellem ventil og ventil og mellem ventil og stempel. 2010-modeller kræver justerbare stødstænger, og tomgangen bør indstilles til 1000–1100 rpm for at undgå klikkende lyde under 900 rpm.

Passer til: Softail 07-17

Produkt-typ Cam Kit
Tillverkarens Art. Nr. 106-4947

551 Easy Start Camshaft Kit

  • Allows for easy start by initially reducing crank compression, but once the engine starts and rpm increases, the compression release lobe is centrifugally retracted and the engine runs normally, with full compression, and without any loss in performance
  • Optimized for 88"/96"/103" to 106" Touring bike with slip-on mufflers and 9.0:1 to 9.0:9 compression with stock starter
  • Bolt-in for stock or mildly modified Touring models
  • Greatly improves low-end and midrange torque
  • Strongest from idle to 4000 rpm
  • Includes camshafts, gearcover gasket, bearings, retaining ring, o-ring, threat lock and instructions
  • Made in the USA
  • Not recommended for compression ratios of 10.0:1 or greater.
  • Installer must check coil bind, valve-to-valve clearance and valve-to-piston clearance.
  • Not for models with OEM compression releases.
  • Can be used with stock pushrods, lifters, and springs (unless noted).
  • Easy Start chain drive 551 camshaft set (CD)
  • 550" valve lift
  • Easy Start Cams make starting easier by reducing the build-up of cranking pressure in the cylinders during starting
  • This is done by lifting the exhaust valve slightly of its seat, with a spring loaded compression release lobe inside the camshaft
  • After starting the compression release lobe is retracted by centrifugal force
  • The only difference is during starting since you will now be able to electric start your Big Inch engine effortless, without the use of big batteries and/or starter motors
  • A stock starter and battery is enough
  • When the engine is running the camshafts function as regular cams, without any loss in power, torque or anything else
  • Note: Only 551, 570, 583, 585, HP103 and MR103 series cams are bolt-in, all others may / will require clearancing and require high lift valve springs
  • Note: Not compatible with kickstart models
  • 2010 will require adjustable pushrods
  • Note: Below 900 RPM you may hear a clicking sound
  • Adjust idle speed to 1000-1100 RPM

Fits: 07-17 Softail; 06-17 Dyna; 07-16 FLT/Touring (NU)