Knastakselsæt S&S Easy Start 551 Twin Cam 99-06

11 681,7 DKK

S&S 551 Easy Start tandhjulsdrevet knastakselsæt
Læs mere

09250453 S&S
  • Easy Start-funktion letter start ved at løfte udstødningsventilen via en fjederbelastet knast, der trækkes ind centrifugalt ved start
  • Optimeret til 88"/96"/103" til 106" Touring-modeller med slip-on lyddæmpere og 9.0:1 til 9.0:9 i kompression
  • Giver væsentligt bedre drejningsmoment i lav- og mellemregistret, stærkest fra tomgang til 4000 rpm
  • .550" ventilløft
  • Tandhjulsdrift (IOG) med indre og ydre drivhjul (4-tandhjulssæt)
  • Indeholder knastaksler, dækselpakning, lejer, låsering, O-ring, gevindlåsning, monteringsdele og instruktioner
  • Kan bruges med originale skubbestænger, løftere og fjedre, hvis intet andet er angivet
  • Fremstillet i USA

Anbefales ikke til kompressionsforhold på 10.0:1 eller højere og passer ikke til modeller med OEM dekompressionsventil eller kickstart. For 99-06 Twin Cam kræves kontrol af frigang og eventuelt ventilfjedre til højere løft. Montering kræver kontrol af ventilfjedrenes bundning samt frigang mellem ventiler og mellem ventil og stempel. Juster tomgang til 1000–1100 rpm for at undgå klikkelyde under 900 rpm.

Passer til: Twin Cam 99-06

Produkt-typ Cam Kit
Tillverkarens Art. Nr. 106-5442

551 Easy Start Camshaft Kit

  • Allows for easy start by initially reducing crank compression, but once the engine starts and rpm increases, the compression release lobe is centrifugally retracted and the engine runs normally, with full compression, and without any loss in performance
  • Optimized for 88"/96"/103" to 106" Touring bike with slip-on mufflers and 9.0:1 to 9.0:9 compression with stock starter
  • Bolt-in for stock or mildly modified Touring models
  • Greatly improves low-end and midrange torque
  • Strongest from idle to 4000 rpm
  • Includes camshafts, gearcover gasket, bearings, retaining ring, o-ring, threat lock and instructions
  • Made in the USA
  • Not recommended for compression ratios of 10.0:1 or greater.
  • Installer must check coil bind, valve-to-valve clearance and valve-to-piston clearance.
  • Not for models with OEM compression releases.
  • Can be used with stock pushrods, lifters, and springs (unless noted).
  • 550" valve lift
  • IOG = gear drive cams with Inner & Outer drive Gears
  • Complete kit with installation hardware, bearings and gasket
  • Easy Start Cams make starting easier by reducing the build-up of cranking pressure in the cylinders during starting
  • This is done by lifting the exhaust valve slightly of its seat, with a spring loaded compression release lobe inside the camshaft
  • After starting the compression release lobe is retracted by centrifugal force
  • The only difference is during starting since you will now be able to electric start your Big Inch engine effortless, without the use of big batteries and/or starter motors
  • A stock starter and battery is enough
  • When the engine is running the camshafts function as regular cams, without any loss in power, torque or anything else
  • They are separately available as replacement from S&S for this kit as 503566
  • Note: No Easy Start Cam grind is bolt-in for these 99-06 Twin Cam models
  • All will / may require clearancing and require high lift valve springs
  • Note: Not compatible with kickstart models
  • Note: Camshafts made before Jan
  • 2010 will require adjustable pushrods
  • Note: Below 900 RPM you may hear a clicking sound
  • Adjust idle speed to 1000-1100 RPM

Includes 4-gear set. Due to the inherent characterics of gear drives, there may be more valve train noise.

Fits: 99-06 Twin Cam (Excl. 2006 Dyna) (NU)