Knastakselsæt S&S Easy Start 583 Softail 07-17

10 177,5 DKK

S&S 583 Easy Start knastakselsæt med tandhjulsdrift
Læs mere

09250450 S&S
  • Easy Start-teknik reducerer startkompressionen via udstødningsventilen for nem start
  • Tanddrevne knastaksler (gear drive) med indre og ydre tandhjul (4-gear set)
  • Ventilløft på .583"
  • Bolt-in-montering, der giver kraftigt drejningsmoment og effekt fra 1500 til 5000 rpm
  • Indeholder knastaksler, tandhjul, pakning til transmissionsdæksel, lejer, låsering, O-ring og gevindlåsning
  • Fremstillet i USA

Montøren skal kontrollere ventilspil, frigang mellem ventiler og stempel samt fjederbundning. Ikke kompatibel med modeller med kickstart eller originalmonteret dekompressionsventil, og årgang 2010 kræver justerbare stødstænger. Juster tomgang til 1000–1100 rpm for at undgå klikkelyde under 900 rpm, tandhjulsdrift kan desuden medføre øget transmissionslyd.

Passer til: Softail 07-17

Produkt-typ Cam Kit
Tillverkarens Art. Nr. 106-5811

583 Easy Start Camshaft Kit

  • Allows for easy start by initially reducing crank compression, but once the engine starts and rpm increases, the compression release lobe is centrifugally retracted and the engine runs normally, with full compression, and without any loss in performance
  • Optimiized for use as a great overall camshaft for Softail and Dyna, but can be used in any Big Twin
  • Provides strong low-end torque and horsepower
  • Strongest from 1500 rpm to 5000 rpm in Softail and Dyna models
  • Bolt-in
  • Includes camshafts, gearcover gasket, bearings, retaining ring, o-ring, threat lock and instructions
  • Made in the USA
  • Installer must check coil bind, valve-to-valve clearance and valve-to-piston clearance.
  • Not for models with OEM compression releases.
  • Not recommended for compression ratios of 10.0:1 or greater.
  • 583" valve lift
  • IOG = gear drive cams with Inner & Outer drive Gears
  • Complete kit with installation hardware, bearings and gasket
  • 88 to 103" engines with compression ratios between 9.7:1 to 10.5:1 and 106" to 124" engines with 9:1 to 10:1 CR
  • Easy Start Cams make starting easier by reducing the build-up of cranking pressure in the cylinders during starting
  • This is done by lifting the exhaust valve slightly of its seat, with a spring loaded compression release lobe inside the camshaft
  • After starting the compression release lobe is retracted by centrifugal force
  • The only difference is during starting since you will now be able to electric start your Big Inch engine effortless, without the use of big batteries and/or starter motors
  • A stock starter and battery is enough
  • When the engine is running the camshafts function as regular cams, without any loss in power, torque or anything else
  • Note: Only 551, 570, 583, 585, HP103 and MR103 series cams are bolt-in, all others may / will require clearancing and require high lift valve springs
  • Note: Not compatible with kickstart models
  • 2010 will require adjustable pushrods
  • Note: Below 900 RPM you may hear a clicking sound
  • Adjust idle speed to 1000-1100 RPM

Includes 4-gear set. Due to the inherent characterics of gear drives, there may be more valve train noise.

Fits: 07-17 Softail; 06-17 Dyna; 07-16 FLT/Touring (NU)