• Blixt&Dunder - precis som det låter
  • Undrar du något? Prova chatten!
Exkl. moms Inkl. moms

Logga in

Namz Can-Bus Controller For Custom Handlebar Switches Non-Bagger Contr i gruppen Reservdelar & Tillbehör / Eldelar / Styrboxar och reglering hos Blixt&Dunder AB (20500245)
Namz Can-Bus Controller For Custom Handlebar Switches Non-Bagger Contr

Namz Can-Bus Controller For Custom Handlebar Switches Non-Bagger Contr

Namz
Betyg på Namz Can-Bus Controller For Custom Handlebar Switches Non-Bagger Contr i gruppen Reservdelar & Tillbehör / Eldelar / Styrboxar och reglering hos Blixt&Dunder AB
4560 kr
 
Köp trots längre leveranstid
Artikelnummer: 20500245
Leveranstid:


CAN Bus Controller

  • A CAN Bus controller is an absolute necessity when changing handlebars and switches on any 11-16 model because of the factory CAN Bus handlebar switch assemblies that make changing these handlebars next to impossible
  • So simple to use, just plug the unit into the factory harness under the fuel tank and wire up any pre-CAN Bus handlebar switch assemblies of your choice
  • Made in the U.S.A,


  • Does not work with keyless ignition bikes

    Connector Style: CAN Bus| Hard Wire
    Units: Each
    Product Name: Control Module
    Type: Handlebar Switch
    Volts: 12 V



    Enhet: Styck
    Produkt-typ: Control Module
    Tillverkarens Art. Nr.: NCBC-N01
    "Can-Bus Controller

  • A CAN-BUS controller is an absolute necessity when changing handlebars and switches on any 11-16 model because of the factory CAN-BUS handlebar switch assemblies that make changing these handlebars next to impossible
  • So simple to use; just plug the unit into the factory harness under the fuel tank and wire up any pre-CAN-BUS handlebar switch assemblies of your choice
  • Made in the U.S.A,


  • "
    CAN Bus Controller

  • A CAN Bus controller is an absolute necessity when changing handlebars and switches on any 11-16 model because of the factory CAN Bus handlebar switch assemblies that make changing these handlebars next to impossible
  • So simple to use, just plug the unit into the factory harness under the fuel tank and wire up any pre-CAN Bus handlebar switch assemblies of your choice
  • Made in the U.S.A,


  • Does not work with keyless ignition bikes

    Connector Style: CAN Bus| Hard Wire
    Units: Each
    Product Name: Control Module
    Type: Handlebar Switch
    Volts: 12 V

    Kundomdömen

    Se fler varor

    Namz Wire Flex Sleeving Id Ø 1/8" 25' Roll (3,18 Mm/7,62 M) Black Cove
    Universal Black Wire Cover

    Available in five sizesSold in 25? rollsFor various OEM or custom ap...
    160 kr
    Namz Heat Shrink Id Ø 1/4" 25' Roll (6,35 Mm/7,62 M) Black Heatshrink
    Shrink Tubing

    Used to cover cables and wiringProtects paint and chromeAvailable in six sizesSol...
    440 kr
    Namz Stamped Pins For Deutsch Dt Connector 100 Pack Pin Deutsch Stampe
    "Deutsch DT Sealed Connector Component

    Refill your Deutsch Builder Kits with these connector co...
    600 kr
    Namz Replacement Mini Fuse 15A 5 Pk Fuse Mini Amp1 5A 5Pack
    Replacement AMP Fuse

    30-AMP Round AGU Fuses

    100 kr